Cinnamon Pull-Aparts

This weekend was chilly and rainy.  With a toasty fire in the wood stove, I decided that we needed some comfort food to go along with the morning coffee.   So I made some Cinnamon Pull-Aparts.  This is a recipe that has gone around and around, and I really don't know who to credit for the original thought, it certainly wasn't me, but I think it warrants repeating.  Here it is:

You will need:

A Bundt pan 
Non-stick spray
3 cans of ready-made biscuits (I use the real inexpensive store brand)
1-1/2 cup brown sugar, packed
3 tbsp cinnamon
1-1/2 sticks or 3/4 cup butter

Preheat the oven to 350.  Coat the bottom and sides of the pan with the non-stick spray.   In a small microwave bowl, melt the butter.  In a separate bowl, combine the sugar and the cinnamon, stirring well.  Open one can of biscuits and place a couple of them into the warm butter.   They will start to puff up a bit.  With a fork, take them out one by one and coat them thoroughly with the sugar mixture.  

 Lay the biscuits standing on edge around the bottom of the pan like this:

Continue until all three cans of the biscuits are in.  You can pack them in tightly if you want, they will pull apart nicely when you are done.  Pour the remaining butter over the biscuits and then pour the remaining brown sugar mixture evenly over the top.  It should look like this:

Place the pan onto the center rack of the oven.  Bake for 20 - 25 minutes, depending on your oven.  To test for doneness, they should separate nicely without being doughy if you try to pull them apart.  They should look like this:

Allow to cool for about 10 minutes in the pan.  Run a non-metallic knife or spatula around the outer and inner edges.  Place a plate on top of the pan and flip it over to remove the biscuits.  It will be all gooey and yummy like this:

Cinnamon Pull-Aparts

They are so yummy in fact that a couple of them didn't survive long enough for the picture!  My husband thought they were wonderful with his coffee, a little pre-breakfast treat. This is a simple and relatively quick way to satisfy the cinnamon roll craving that comes in the fall, but with only a fraction of the work.  Enjoy!!

Tammie

Farm Photos

I follow a photography blog where they feature different photographers and their art.  There are some amazing photos here, and some really awesome farm pictures.  Check them out at Photography Blogger and search "farm"  You will see some incredible talent.

Tammie

Home made salsa --and how to use it to season steak

Did I mention this was a great garden year? Here it is two days before October and we have not yet had a frost.  This has been a blessing especially for my neighbors who started heirloom tomatoes from seeds.  The seedlings did so well, that they ended up planting 103 tomato plants!!  Needless to say they have been supplying tomatoes to many lucky people who are fortunate enough to live nearby.  I am blessed to be one of them, and along with the tomatoes from my own plants, I have had plenty to make all kinds of wonderful dishes.  
Now, I like salsa.  The flavor combination of all the ingredients is delightful, but I like it MILD.  It is difficult to find really tasty MILD salsa.  So years ago, I started experimenting with different recipes to come up with one that is both mild and flavorful.  If you like heat, this one is not for you, but if you, like me, do not like the feeling of a burning tongue when you eat salsa, give this recipe a try.  I found the basic recipe in the "Better Homes and Gardens Presents America's All-Time Favorite Canning and Preserving Recipes" book (copyright 1996).  It is on page 39 entitled "Chunky Homemade Salsa" and modified it to meet our family's taste.

You will need:

An 8 quart stainless steel pot
Colander and large bowl to set it in
Large heat resistant spoon for stirring
4 cup measuring cup
Water bath canner or large stock pot to process the jars of salsa
Jars and lids for canning (see canning tips in my other post, or go to Ball (TM) Getting Started With Canning for more information.)

Assemble the tools above.  Wash jars and lids and place in the dishwasher or a pan of water and heat them.  Keep them hot until ready to fill.  Prepare the fresh ingredients:

8.5 lbs of tomatoes (about 25 medium)
4 or 5 Anaheim chili peppers
3 jalapeno peppers
3 or 4 sweet bell peppers
2 cups coarsely chopped onion (about 1 large onion)
3/4 cup finely chopped fresh cilantro
6 cloves garlic, minced 
1/2 cup vinegar
1 tbsp granulated sugar
1 tsp salt
1 tsp ground black pepper

Wash, seed and core the peppers.  (Tip:  Wear rubber gloves while working with the peppers to prevent the oils from burning your hands.)  Measure 1/3 cup jalapenos, and 2 cups of Anaheim and bell peppers combined.  Place in a large bowl.  Chop onion, measure and add to peppers.  Mince the garlic and chop the cilantro and add to the peppers and onions.  Add the vinegar, salt, sugar and pepper to the bowl.  Set aside. 

Wash, peel, seed and core tomatoes.  (Tip:  Dip washed tomatoes in a pot of boiling water for 10 - 15 seconds then transfer to a bowl of cold water.  The skins will come off very easily).  Cut the tomatoes in half or quarters and put in the colander over a bowl and allow to drain for 30 minutes.  Coarsely chop tomatoes and measure out 16 cups and place into the stainless steel pot.  Cook over med-high heat, stirring frequently until boiling.  Reduce heat and allow to simmer for 45 minutes or until thickened to desired consistency while continuing to stir frequently.  (Tip:  If you use a heavy bottomed pot, it will be less likely to stick or burn.)  Add the pepper mixture and return the sauce to boiling increasing the heat to med-high and stirring frequently.  Once the mixture reaches boiling, you can remove from heat.

Fill the large stock pot or canner with hot water and set on stove top to heat.  (Tip:  If you live in an area with hard water, add 1/4 cup of vinegar to the water in the canner to avoid a white scale from forming on your jars.)  Put the canning lids into a small pot with boiling water.  Remove from heat and set aside.  Ladle hot sauce into hot jars and wipe the rims with a clean, wet cloth.  Put the lids in place and secure the bands.  Put into the canner and submerge in the hot water.  There should be at least 1 inch of hot water over the top of the jars.  Bring to a boil and process half pints or pints  in the water bath for 35 minutes.  Remove from  the canner and set aside to allow the jars to seal.  Once they are sealed you can store them in your pantry.  This should yield you about 6 pints.  

It seems that whenever I make a canning recipe, there is always some left over after I've filled all the jars, not quite enough to fill another.  This was the case today, and I had about a 3/4 cup left over.  As it happens I had thawed some steaks for dinner and thought I'd try something different to season them before grilling.  This is what I came up with:

3/4 cup fresh home made cooked salsa
2 tbsp taco seasoning (McCormick's, French's, Schilling, whatever brand you have).
1/2 tsp ground cayenne pepper
1 tsp ground black pepper
1/2 tsp ground paprika

Combine these ingredients and stir thoroughly.  In a large bowl, place a little of the sauce on the bottom and add a layer of steaks.  Spoon a generous amount on top of the steaks and spread over them completely.  Add another layer of steak and spoon more salsa mixture on top.  Continue until all your steaks are layered with the sauce.  Cover and set aside for at least 1/2 hour.  Prepare your grill and heat it to high.  Place the steaks with the sauce on the grill at high heat for 1 - 2 minutes and turn over.  Spoon any remaining sauce over the steaks and sear for 1 - 2 more minutes.  Turn the heat to low and cook until done to your desired taste.  I served this up with a simple salad and fresh corn on the side.  It was delicious.  I hope you have the opportunity to try this. Enjoy!


Goodnight,
Tammie

Building a chicken brood pen

Friday was a great day.  I decided I needed a new brood pen for my chicken coupe since I have a momma with a baby.  I priced out the ones at the feed store and they were about $120.00, too rich for me.  So I built one.  I like to reuse old wood for projects like this, because I don't mind if the boards don't match. Eventually they all change color and fade, so it doesn't matter and it saves a lot of money.  In this case, the only thing I had to buy was hardware for the door and hardware cloth, which cost me about $45.00  You will need:

table saw (to rip the boards)
chop saw or small skill saw
power screw driver
power drill
small square 
Level
tin snips to cut the hardware cloth
stapler with staples
three 2x4's cut to 36" and 4 scrap pieces 6-8" in length
one 2x4 cut to 27"
four 2x2's cut at 36"
four 2x2's cut at 27"
five 2x2's cut at 24"
four 1x2's cut at 27"
four 1x2's cut at 24" 
1 1/4" screws
2 1/2" deck screws
3" deck screws
a drill bit that is the same diameter as your deck screws.
screw driver tip to match the heads of the screws (phillips, roberts, etc)
hardware cloth
one pkg of two small hinges
window sash lock (one or two)

I started with several boards that were at least 24", 27" and 36" in length.  I ripped them down on the table saw to make them into 2x2's and 1x2's. (2x2's are actually 1-1/2 x 1-1/2" and 1x2's are actually 3/4" x 1-1/2")  You can buy the lumber and start with new wood if you need to. Cut your wood to length as outlined above.  To make the top of the pen, lay two of the 36" pieces and two of the 27" pieces out like this:

building a chicken brood pen square up the corners

(Tip: If you use a flat surface and a square to match up the corners, you will have less problems later with wracking or twisting of your project.) Drill a hole at the end of the 27 inch piece completely through the board.  By pre-drilling all your holes(through just the 1st piece of wood) you will avoid splitting the ends and ruining your piece:

build a chicken brood pen -  pre-drill the corners

(Tip: If you drill the hole at a slight angle, it will prevent the pieces from rotating on each other.)  Drive a 2-1/2" screw into the hole and into the perpendicular piece of wood:

build a chicken brood pen - screw together the corners

Continue this process all the way around until the four boards are connected into a rectangle.  Repeat this process for the bottom but add a center support board 24" long in the middle like this:

build a chicken brood pen -  floor

Cut your hardware cloth with tin snips to fit the top and the bottom and staple in place.  Next add the upright pieces 24" to each corner pre-drilling through the top or bottom as before.  Be sure you have the hardware cloth on the top of the bottom piece before you place the uprights:

build a chicken brood pen

 You will now have a box with no sides.  Decide where you are going to place the brood pen.  I chose the southwest corner of my chicken coupe near the electric outlet so I can add a heater when I need to:

build a chicken brood pen -- choose the location

  I decided to put it up off the ground, so this requires some bracing.  I took two of the 36" 2x4's and cut a bevel at each end 45 degrees facing each other.  You can do this on the chop saw or with a skill saw.  (Tip: If you tack a small piece of 2x4 scrap with 2 screws to the ends of the boards it makes it easier to attach to the wall and to the pen):

build a chicken brood pen -- support boards

Then I measured how high I wanted the bottom to be, and drew a line on both walls (Tip: if you use the level as your strait edge, you can draw your line perfectly strait and level at the same time).  Next attach the remaining 36" 2x4 to one wall and the 27" 2x4 to the other.  These will act as ledger boards and your pen will sit on top of these.  Using the level again, hold your support boards against the wall and lay the level from the ledger board to the top of the support board.  Mark a line where the support board meets the wall and pre-drill and screw the supports to the wall below the 36" ledger board.  Put the brood pen on top of the ledger boards and secure with 3" screws to both the ledger boards and the wall, getting at least a couple of the screws in the wall studs.  Use a level to adjust the support boards and screw them into the bottom of the pen remembering to pre-drill your holes:

build a chicken brood pen -- screw in the supports

Cut some additional hardware cloth to go along the outer side of the pen.  To make the door, take two of the 27" 1x2's and two of the 24 1x2's and put them together in the same manner as you made the top or bottom of the pen.  Cut hardware cloth to cover this square and staple in place.  Take the remaining four 1x2 pieces and place them on top of the section you just made, taking care to reverse the order of the boards so that the ends overlap.  Using 1-1/4" screws, pre-drill the holes and screw them all together.  This makes a nice secure door that won't twist.  Using the hinges, attach the door to the pen at the top.  Because my pen was against the wall and the door fit nice and snug, I was able to use just one window sash lock.  I installed this on the side.  You are now ready to put your pen to use:

build a chicken brood pen -- finished project

I put momma hen and her baby inside, which gives her significantly more room than in the dog kennel.  Also, with the hardware cloth floor, spilled water and refuse falls through to the floor below, which keeps the pen drier and tidier. 

 Now for the evening task of picking, husking and freezing corn.

An evening's chores and homemade pasta sauce

Good evening. Here is tonight's clutch.  I love the subtle color differences in the individual eggs, they are so pretty!  Too pretty to eat, almost.

 

Spent a little time with the cows too, gave them a new bale of hay, they are very happy now.  This is Pansy, my little 3 month old heifer.

 

She is learning to lead.  I am a firm believer in tame cattle, as they are much more predictable and easy to handle than wild ones.  

Dinner tonight was pasta with homemade-from-scratch sauce.  It takes several hours to prepare, but can be made ahead and canned in a water bath or frozen. Recipe:

Home made Pasta Sauce  (Yield 6 pint jars)

20 large or 30 medium tomatoes.
2 cans chopped olives
about 6 - 7 medium mushrooms chopped
6 cloves of garlic (roasted - see below)
1/2 cup finely chopped onion or 2 tbsp dried onion
2 tbsp finely chopped fresh basil
2 tbsp finely chopped fresh parsley
1 tsp finely chopped oregano
2 tsp garlic salt (or to taste)
1/4 tsp garlic powder
1/4 tsp onion powder
1/8 tsp fine black pepper
1tsp olive oil (to roast the garlic)
2 tbsp ketchup 
1/4 to 1/3 cup brown sugar (to taste)
1/4 c vinegar

Peel, core and seed the tomatoes. (Tip: Put the tomatoes into a pot of boiling water for 20 - 30 seconds then plunge into cold water.  The skins will slip off much easier!)  Let drain for 30 minutes in a colander over a bowel to remove some of the water.  Puree all but 3 cups of the tomatoes in the blender or food processor and pour into a large stainless steel pot.  Coarsely chop the remaining tomatoes and add to the puree.  Cook for 1 - 2 hours over med-high heat stirring frequently to prevent burning. (Tip:  If you use a heavier pot, it won't burn as quickly).  This will reduce the volume by approximately 1/2. Meanwhile, place the unpeeled cloves of garlic in a piece of foil and drizzle the olive oil over the top.  Wrap tightly and place on an oven safe dish in a preheated 400 degree oven for 15 - 20 minutes. Remove from the oven and allow to cool.

Once the tomato puree has cooked down, remove the garlic from the foil, cut in half and squeeze the cloves from their peels and mince.  Add the minced garlic, olives, mushrooms and onions to the mixture and cook until softened.  Add the herbs, seasonings, vinegar, ketchup and brown sugar.  Adjust the seasonings to taste if you desire.  Cook for an additional 30 minutes.  Ladle hot sauce into hot jars leaving 1/2 inch of head space.  Place lids and screw bands and process pints in a water bath for 35 minutes.  (Tip: Get canning parameters from your local county extension office or refer to Ball (TM) Getting Started with Canning for more information.)  Alternately you can place in freezer-safe containers and freeze for up to 6 months.  Enjoy any way you would ordinarily use store-bought pasta sauce, but with the knowledge that you are bringing the freshest ingredients to your family's table.

Let me know how you use pasta sauce, or if you have a recipe you'd like to share.

Tammie









 

September 26, 2013

It is amazing outside right now.  No frost yet, a remarkable thing given that we often have a frost by late August.  This has been an unusual garden year, corn and tomatoes coming out of my ears (pun intended!).  The chickens are laying beautiful eggs now, and one momma hatched out a chick just last weekend.  It is awesome to see the little one following her mother all over the yard, and to watch the hen fight off all comers, even the other chickens.  
Well, I'm out to the barn to feed and water the chickens and gather the eggs.  Does anyone have a great recipe for deviled eggs they'd like to share?

Welcome to my blog

I'm a farm girl heart and soul.  Raised on a farm, and continue the tradition in my own life now.  My passion is farming and I want to spread the fever!  I want to inspire you to go out and grow something.  I want to share what I've learned, and learn from others.